Real Questions for DELL EMC DES-DD23 Exam

Looking for the latest questions for Specialist Implementation Engineer-PowerProtect DD Exam DES-DD23 test? We have cracked the latest questions for DELL EMC DES-DD23 test, which are the best guides for you to test all the related topics. Besides, DES-DD23 exam contains two parts. Each candidate needs to pass both parts to pass the DELL EMC DES-DD23 exam. Share some free DELL EMC DCS-IE DES-DD23 real questions below.

Page 1 of 2

1. A PowerProtect DD system is configured for VTL. The backup application requires a minimum tape capacity of 800 GB.

What is the minimum tape type to support this requirement?

LTO-5

LTO-3

LTO-2

LTO-4

2. Backup administrators have noticed slow backups on the AIX environment.

To fix the issue, what should the set large_send be for each NIC, and what should the NFS option be set to?

no and nfs_rfc1323=0

yes and nfs_rfc1323=0

no and nfs_rfc1323=1

yes and nfs_rfc1323=1

3. What is a requirement to configure the PowerProtect DD tape out to cloud feature?

Two cloud units

Cloud Tier Capacity License

Tape Out to Cloud License

DDVE in the Cloud

4. Which protocol is used for communications between a PowerProtect DD appliance and cloud tier to Dell EMC ECS?

SSH

SSL

FTP

HTTPS

5. What is a requirement to use the PowerProtect DD HA feature?

Each head unit requires its own FS25 shelf

Head units and nodes require an active/active configuration

A single set of shared storage

Dual set of shared storage configuration

6. A backup administrator needs to implement BoostFS for Windows .

What do they need to install on the Windows server?

NFS

FUSE

CIFS

CBFS

7. Which enterprise applications does the DDBEA agent support?

Oracle, Microsoft Sharepoint, and Microsoft SQL

Microsoft SQL, Sharepoint, and Exchange servers

SAP with Oracle, IBM DB2, and Microsoft active directory

IBM DB2, Microsoft SQL, and SAP HANA

8. What is the preferred method to ensure backups are protected against deletion or corrupt?

Encryption

Dell EMC Cloud Tier

Retention Lock

Data Invulnerability Architecture

9. What system role is required to create the second security officer for a PowerProtect DD?

admin

sysadmin

limited-admin

security officer

10. A storage administrator finished the zoning between the PowerProtect DD and the NetWorker backup server .

How can they verify that the zoning was completed properly and

the server HBA are visible?

scsitarget initiator show list

scsitarget show initiator list

scsitarget show initiator

scsitarget initiator list

Page 2 of 2

11. A customer needs an upgrade on their DD6900 to use HA .

Which expansion shelf is required?

ES40

FS25

DS60

ES25

12. Which PowerProtect DD procedure uses the DoD/NIST standards to provide data security?

Data Sanitization

End-to-End Verification

Replication Encryption

Encryption

13. An engineer is configuring a PowerProtect DD system for VTL using Fibre Channel .

How should the zones be configured?

Hard zones

Single initiator, multi target

Single initiator, single target

Soft zones

14. An administrator monitors the performance statistics of a PowerProtect DD appliance. Low disk-write rates are shown, and the network inbound traffic is high.

What is the most likely cause of this behavior?

NVRAM failure

Disk failure

Expired segments

Known segments

15. When using CIFS from a PowerProtect DD system, what should be changed on a Windows machine?

SMBTimeout to 7200 seconds

CIFSTimeout to 3600 seconds

SESSTIMEOUT to 7200 seconds

SESSTIMEOUT to 3600 seconds

16. Which component of PowerProtect DD is Data Invulnerability Architecture a feature of?

VTL

DDOS

DD Boost

CIFS

17. A backup administrator is tasked with verifying the compression savings of a PowerProtect DD9900 .

Which compression algorithm will they see enabled by default?

lzw

gzfast

18. Refer to the exhibit.

To which shelf and port should SAS HBA slot 1 port B be connected?

Shelf 04 BH

Shelf 01 BH

Shelf 04 BE

Shelf 01 BE

19. An administrator recognizes poor network performance when using CIFS shares from a PowerProtect DD system. The network link utilization is under 100%.

What is the most likely cause of this issue?

TCP window size too small

TCP timeout too small

TCP timeout too large

TCP window size too large

20. DRAG DROP

What is the correct sequence of operations used by the PowerProtect DD DIA in the end-to-end verification process?